For these infant leather moccasins, you’re going to want to use a soft leather. You’re going to cut your vegan leather and animal leather the same way. I like Cricut Leather because it is soft and perfect for those baby toes.
Step One – Lay your leather smooth side down on your Cricut mat. If you find that your leather is grainy or won’t stick to the mat well, lay some transfer tape on the fuzzy side and then apply that side down on your Cricut mat.
You can also use some painters tape or masking tape to hold down the edges of the leather. Cricut recommends using the Strong Grip Mat but I have also used the Standard Grip Mat or the Fabric Grip Mat and it held fine.
When you cut leather with the Cricut Rotary Blade, you get a cleaner cut. The rotary blade isn’t pulling the leather like the Deep Cut Blade would do and so you’re not going to go through materials quickly.
Step Two –Open the Design Space project using this link here or search for it in Design Space.
Move your small white rollers all the way to the right so it doesn’t make a mark on your leather.
I chose to edit the material settings for canvas. I just adjusted the force setting to 400 so that it would cut cleanly through. I chose more pressure before I cut as well. This gives an extremely clean cut. If you’re using a desktop computer and you have the knife blade, use that. This is a way that you can kind of jimmy rig your mobile device to cut the leather just as good as the Cricut Knife Blade.
Remove your cut baby shoe pattern from the mat and set aside.
Step Three – Take the fringed back piece and the larger rectangle and sew them right side to the wrong side along the solid leather.
Flip the fringes piece over itself and then create a loop so that the elastic will fit through. Sew about 1/2” from the top of the fringe piece.
Step Four – Take the small fringe piece and the toe piece and sew it on top of each other. You’re going to want to have them laying right side up. Stitch right along the top as close as you can. Then about 1/4″ below that, stitch another straight line. Be sure to reinforce the edges of each stitch.
Step Five – Find the center of the sole of the shoe and the large fringe back piece. Follow along the curve and clip them together in place. Sew a 1/4″ seam along the edges.
Sometimes trying to get the Cricut leather to curve can be difficult. If you need to, just do the sides and then hand stitch the back curve, that works just as well.
Step Six – Take the sole of the shoe and the toe piece and place them right sides together. Start by using a binder clip and place it in the center holding those two pieces together. Then follow along the curve of the toe and begin by stitching the shoes together using a 1/4″ seam.
Step Seven – Turn the shoe right way out and then use a dowel or a bone folder to push the leather seams out to smooth out the shoe.
Take a small safety pin and thread the elastic through the shoe and pull them taught. Sew a zig-zag stitch across both ends together and then clip. Tug at the top of the shoe to try and shimmy the elastic so that the part where they connected is hidden.
Did you know you can use stencil vinyl and your Cricut Explore to make DIY nail decals? Read this post to find out how easy it is to create nail stencils and make your own nail art. This post contains affiliate links. At no extra cost to you, I receive a small commission from your purchase. Thank you for your support.
I love DIY nail art just like the next person but I had never tried to create my own DIY nail decals before. I grabbed some stencil vinyl from Expressions Vinyl and cut it with my Cricut Explore and it turned out perfect. Next time I attempt it, I will use brighter colors but I’m not a bright nail person. I already own a mini OPI light so I’m able to do my own gel polish at home and that’s just what I’m going to have to do from now on. You can find a similar system here but I got my OPI kit at Sephora and it came with all the basics. You certainly don’t need a light to do this and this can be done with regular nail polish. Just allow it to dry for quite a while before painting on your decal.
I painted my nails with the gel base coat and allowed it to set in the light for 20 seconds each hand. I then painted one coat of black and I had them set under the UV light for another 20 seconds. Next, I topped it off with the no wipe top coat and let that set under the light for at least 30 seconds. I did wipe them with alcohol before I put that chrome powder on so that I would have a clean nail and I’d get a good shine. Don’t use too much of the powder, a little goes a long way. Rub the powder into your nail until you see the shine that you want. You can use an eyeshadow applicator or a makeup sponge wedge. Next, you’ll apply your Unicorn decal that we’ve cut with our Cricut or any other cutting machine you have and then apply the black paint. Allow it to set with the light for 20-30 seconds to be sure that the decal won’t go anywhere. Place another top coat on and set it under the light for an additional 30 seconds. Here is a great tutorial on how to cut vinyl with your Cricut and here is one on how to cut with your Silhouette. Because these are so small you won’t really need transfer tape. I just used a weeder tool and removed it straight from the backing and put it straight onto my nail. Here is a great youtube tutorial on using it with the Sally Hansen gel polish where you don’t need a UV light. To get a kit of all the colors and applicators without the UV light, click here. Again, you don’t need to use the chrome powder or fancy polish. This is your own, go for it!
Create this DIY LEGO Batman shirt using your Cricut and glow in the dark iron-on vinyl. It’s perfect for the little vigilante in your life. This post does contain affiliate links. Thank you to LEGO for sending our kids these awesome books.This post does contain affiliate links.I don’t know about you but LEGO Batman has become an essential in this house, or should I say the car? It’s pretty much the only DVD my kids want to watch in the car and because of that, I’ve become really good at quoting the movie. We took Siaki and his friends to see it when it was in theaters and I’ve never seen kids laugh louder in my life. These shirts have become their go-to wardrobe because the glow in the dark vinyl lights up for a good 5-6 hours after they’ve been playing outside all day.
Go ahead and upload the LEGO Batman shirt cut file into your computer using this method. It has both images on the file so you can upload both or just one. You do that by selecting whatever part of the image you don’t want. So for the words in Batman’s logo, you’re going to select it so that the Cricut will know to cut it out. This Batman cut file can be uploaded on your Silhouette but it’s been so long since I’ve done that. There are plenty of instructions on how to do that online.After you’ve uploaded your file, size it to fit the shirt. For a child large and medium, I made the file about 8.5″ wide. Set your file to cut and be sure to mirror the image for iron-on. Once your image has been cut, remove the excess iron-on material. Only leave what you want your image to be on the carrier sheet.
To secure your image with an iron, follow this method. If you’re using a heat press, your temperature needs to be set for 305° and pressed for 20 seconds. Cricut has a new EasyPress and I’m excited to get my own. For now, I just used the iron.There you go. You’ve now become the coolest mom on the block cause your child has their own LEGO Batman shirt and they can put together all their LEGO Batman sets while looking good.
Start by uploading the cut file into Design Space. You can find an easy tutorial here. It’s relatively easy and it’ll be saved to your Design Space files forever!When cutting the luster finish of Expressions Vinyl, it can be a little thick. Use the iron-on + setting on your Smart Dial and cut once. While your vinyl is still adhered to the mat, weed your image. The thinner the letters, the harder the removal is but if you go slowly, it can be done. Lay your transfer tape over your weeded image and press firmly with your scraper tool.Once the image is transferred, lay it on to your tumbler and voila, you’re finished. You can pretend your Shelley Long doing the Freddy on your front lawn. 😉
Making this DIY Patriotic Shirt is easier than you could ever imagine. Use the Cricut Foil Iron-On to give it lots of flair. This post contains affiliate links. Thank you to Cricut for sponsoring this post.
I love using foil iron-on and Cricut by far makes some of my favorite iron-on vinyl. We’re fortunate enough that my kids get to celebrate two cultures. Fireworks play a huge role in their American heritage and their Tongan heritage. For this post, since we’re here in Utah, I’ll be making a DIY Patriotic Shirt and sharing with you the Cricut Explore cut file.
The foil iron-on is just as easy to use as the standard iron-on but it is a little thicker so you have to use your custom settings on your Smart Set Dial. It will be available in the drop-down menu where you select your custom material and use the Neon Iron-On setting. Be sure you remember to mirror your image or you’ll hate yourself for wearing a backwards shirt ;).
You’ll want to follow this method for using Iron-On, warm up your shirt first with the iron and then place the Iron-On where you desire. This starts the bond almost immediately and you won’t get lifts that are almost always problematic if you’re not used to this material. Make sure your iron is set on medium heat with no steam and be sure to allow it to cool for a few minutes before peeling off the carrier sheet.
The shirt is going to be the background color so that is why I chose a white shirt. I laid my red iron-on first and let it hand under the heat for about 10 seconds using a lot of pressure. Peel up the plastic and then do your blue iron-on, making sure I didn’t touch the hot iron to the red foil. You will now match up the silver to form the USA. I have already sliced your image so it’s set to go and you don’t have to worry about any of the designing.Once all your foil is on the front of the shirt, turn it inside-out and press really well on the back to ensure a tight seal of the foil. When you care for your shirts, wash them inside out on gentle.
Now enjoy the DIY Patriotic Shirt and party the night away. Happy Independence Day!!This is a sponsored conversation written by me on behalf of Cricut. The opinions and text are all mine.
This shop has been compensated by Collective Bias, Inc. All opinions are mine alone. #BlueLizardSummer #CollectiveBias
Learning how your child reacts to the sun is always a fun experiment! Even though they share the same genetics, siblings often times react differently to the sun. My older three brown right up and then you have my baby who burns just like his mama. I’m going to give you some of my best sun care tips for toddlers so buckle up!
We were in Tonga over the winter (their summer) and we had to leave early because Malakai couldn’t handle the heat. It was so hot, like Arizona heat but with 85% humidity hot. No fun. I’ve never experienced heat like that and hopefully I never will have to again. Malakai was extremely sensitive to the heat there too. I’m not sure if it had to do with his prematurity or if he had somehow contracted a mosquito-borne illness. He’d toss-and-turn all night long, never napped and he was pretty much the grumpiest he’s ever been. I needed to learn quickly how to take care of him in the sun.The only thing he ended up loving was being dipped in the ocean and then laying down in the shade. Obviously that wasn’t always an option so we had to get creative with how we dealt with him overheating. Some of my favorite ideas are:
Sunscreen and a higher SPF than you think you’ll need. Toddlers skin is still so fragile and thin that they need extra sun protection. Don’t be afraid to try the Blue Lizard® Australian Sunscreen out for yourself. How you take care of your skin when you’re young will determine how it looks when you’re older.
Rompers and lots of them. The fabric in these rompers are fantastic. They’re extremely breathable and come in different sleeve and pant lengths. These were a huge lifesaver in the heat and I ended up buying more of them once we came home.
Hats and large ones too. The wider the rim of the hat, the more area it’ll cover. I do like those hats that look like a towel is hanging down, but fashion over function for me and so I like to stick with bucket hats. Be sure that there is a strap to secure it on your baby’s head. But also make sure that the secure tab can easily come off, like a velcro one.
SPF proof swimwear in addition to your sunscreen. There is never too much sun protection and get all the coverage you can find. I love that swimwear now is available with additional SPF because you can’t always swim in long sleeves and pants.
Water, water, and more water. Toddlers need hydration as much as adults and they’ll feel miserable too if they don’t stay hydrated. There is always that rule of drink before you’re thirsty. Stay on top of it and be sure they’re getting the amount they need.
Washcloths. Dip these in the cool water and place it around your child’s neck. This has an immediate effect on how your body feels and it can help them get the energy they need so that you can get them out of the heat.
Babies and ourselves need a lot of sun coverage for our skin. In the last few years I’ve had moles removed which were on the cusp of being cancerous. I’ve been more diligent to cover myself and my children more because of this. Tonga was by far my worst sunburn and so while we were there I made sure to cover them in Blue Lizard® sunscreen before they even started for the day. I knew they’d run off to the beach and sunscreen would be impossible for them to remember.I love the Blue Lizard® Baby Sunscreen especially for Malakai’s sensitive skin and you can easily find it at your local Walmart. But the most important feature I love is that the Patented Smart Bottle™ technology – bottle changes color when exposed to harmful UV sunlight. This can be used as a great teaching tool for your kids on when to re-apply sunscreen (only the bottle will change colors). Just remember to consult your pediatrician before applying sunscreen to children younger than 6 months.Tell me, what are your favorite sun care tips for toddlers? Also don’t forget to download the Ibotta app where you can get a $4 rebate just for purchasing Blue Lizard® Baby Sunscreen.
I did receive this shirt from Cents of Style as part of compensation for this post. All opinions are my own and this post does include affiliate links.
What is being brave? I don’t know if I have one answer for that. Being brave to me is trying something you’ve been afraid to do. You finally have that exhilaration that you’ve experienced something you never thought you’d try or would have to face. Being brave to me has different meanings in different situations. One thing I’ve struggled with my entire life is my weight. I’m finally past all the issues of what others think of me but I’ve had a hard time getting over the things that I think of myself. I’m extremely critical of myself and I hate that I physically cannot do things I want to do. If you follow me on Instagram, you may have seen a few weeks ago that I posted on getting stomach surgery to help with weight-loss. Being brave has helped me face that I need intervention to help myself.Some may see that this is an easy way out but it’s far from easy. In 2006 I had a lap-band placed on the top of my stomach to help restrict the amount I eat. The last ten years I have figured out ways to manipulate it so that I can eat more than what I am supposed to. In that it has led me to bulimic tendencies because I’ve been too afraid to face the truth and food has always comforted me.
I’ve learned that throughout this process I have to face real life and I cannot hide behind food anymore. I think the reason the lap-band didn’t work for me is because I hadn’t faced real life. Now I am more than ready. I’ve had physiological help within the last year to help me deal with the issues of overeating. I’ve faced my own issues of suffering from Post-Partum Depression and PTSD. I’ve faced the fact that if I don’t do something drastic now then I never will.I’ve had a very low quality of life these last few years since I had my baby and I don’t want to do it anymore. That’s why I’ve chosen to be brave and to have a gastric bypass on May 22. I’ll detail my progress on Instagram but I also want others to know that it’s OK to be vulnerable and it’s OK to face what we’ve all been hiding from. It’s now time to be brave, it’s time for me to just be me.
I love Cents of Style for so many reasons but one of the biggest reasons is that they’re a champion of others and support others to no end. I hope that you get a shirt to help remind you of what you can do and what you can accomplish!I also wish I got better pictures of my shirt but it was a reminder for me under my button up to continue to be brave. I basically folded my arms the entire time because I wasn’t being brave this day. And we’ve also aged because most of our conversation included who is nice and at what store we’re willing to revisit because they had great customer service…I do love my friends though!
Using Cricut’s Make It Now feature is easier than you think. Just choose your project and press go! Create this paper floral crown with your Cricut Explore.This post contains affiliate links. Thank you to Cricut for sponsoring this post.
Have you ever wondered how the Make It Now projects work in Cricut Design Space? It is probably my most favorite feature that Cricut launched when they first launched their Cricut Explore. I’m going to be showing you how to make a floral crown with your Cricut Explore. I’ll be using just simple cardstock and some glue and all my measurements are done for me with the Make It Now feature.How I chose this specific project was select the Fashion category from the drop-down menu on the upper right corner of Cricut Design Space. I selected the project I wanted and then all I pressed was Make It Now! Everything is measured out for me and they tell me what colors and how many pieces of each material I need in the information page.
Cut all your needed flowers and leaves and use this Giant Paper Flowers booklet to help you learn to put the flowers together correctly. Once you have them all together and then begin to assemble your floral crown.I started by braiding the floral stem together with 2 kinds of ribbon. I used 3/8″ wide ribbon that I picked up from my local Michaels along with the floral wire stem. I took it against my daughters head so that I’d have the right circumference. Her head was just the right shape so I didn’t need to cut any additional wire. I did leave longer tails of the ribbon so that I could tie it in a bow at the back and it’d have some texture.Once the wires were braided together and the flowers were assembled, I glued it right to the wires. I just placed them as I wanted them and that was it. Cricut’s Make It Now feature is so easy to use and all the supplies are listed for you so you know what you’ll need ahead of time.
For more Cricut inspiration, see my Cricut projects here.
This is a sponsored conversation written by me on behalf of Cricut. The opinions and text are all mine.